Tel: +1-518-608-6479      
    LessEMF.com         Earthing and Grounding Clips, Cords and Connectors  
Anti-static accessories for EMF Shielding    
search by part numberSearch by Part Number          E-mail    Fax/mail order form     Cart      
 Earthing grounding
.
.
.


Vehicle Ground Strap Vehicle Ground Strap Vehicle Ground Strap

VEHICLE GROUND STRAP

"Maintains Electrical Connection to Ground"

Like a Grounding Wrist Strap for your car! No one likes that awful big shock when getting out of an automobile or truck. That shock is the discharge of "chassis voltage" built up as the vehicle moves along the highway. This type of discharge causes serious problems when it occurs at the gas pump. Every year, this seemingly innocent spark occurs at the wrong place and the wrong time: igniting gasoline vapors while fueling the vehicle. This is prevented by grounding the vehicle.

The Vehicle Ground Strap can be used on any car or truck. Simply affix the strap's clamp to the chassis of the vehicle and allow the conductive strap to dangle to the ground. Safe, durable and unaffected by the weather, the Vehicle Ground Strap maintains a secure ground and electrically neutral vehicle. Makes a great gift too. 18" long, 1 year warranty.


Vehicle Ground Strap (Cat. #A214) ……… $19.95 add to cart



GROUND TESTER GROUND TESTER

GROUND TESTER

Need to verify that your ground connection is working? This little device can check two ways:
   - Verify the conductivity of your grounding material
   - Verify if you are adequately grounded

Just push the button. LEDs will illuminate to distinguish 3 levels of conductivity:

  • Yellow: greater than 10 MegOhm (poor conductivity)
  • Green: 750 kOhm to 10 MegOhm (adequate conductivity)
  • Red: less than 750 kOhms (good conductivity)

Very simple to operate. Instructions are printed on the back of the unit. Includes North American style ground cord. Uses one 9V battery.

Ground Tester (Cat. #A185) ……… $19.95 add to cart



GROUNDING CORDS

Gator to Gator

Grounding Cord Insulated copper wire with standard alligator clips on the end. Connect it to magnetic shielding foil to add e-field shielding capability or use it to attach computer monitor shields, conductive fabric, or conductive painted surfaces to ground. Also great as an extension for grounding wrist and waist straps. Other lengths available as special order ($1 per foot)

Alligator clip on each end:
Grounding Cord, Gator/Gator, 18 inch (Cat. #A295-18) ...... $2.00 (insulated clips) add to cart
Grounding Cord, Gator/Gator, 60 inch (Cat. #A295) ............ $8.95 (insulated clips) add to cart


Banana to Gator

Grounding Cord You get 3 cords (1 each: red, black, and yellow) with banana plugs on one end and alligator clips on the other. Use them as ground cords, in meters, test equipment, etc. 36" long.
Grounding Cord, Banana to Alligator (Cat. #A298-C) ...... $3.79 add to cart



Grounding Cord

Plug to Gator

Alligator clip on one end, 3-prong molded plug on other end. Easiest way to ground fabrics, drapes, plastics. Six feet long. Only the round lug is connected to the wire. The 2 flat prongs are not connect to anything.
Grounding Cord, 3-prong/gator 6ft (Cat. #A295-3) ...... $8.95 add to cart



Grounding Cord

Plug to Clamp

Need a bigger gator? This version has the large clamp with 1 inch opening, outlet plug on the other end. 6 foot cord.
Grounding Cord, 3-prong/clamp 6ft (Cat. #A295-4) ...... $8.95 add to cart



Grounding Cord

Plug to Ring

Ring Terminal on one end, molded 3-prong safety plug on other end. Six feet long.
Grounding Cord, plug/ring (Cat. #A295-3-Ring) .... $8.95 add to cart



Grounding Cord

Gator to Clamp

Alligator clip on one end, Ground Clamp on other end (great for grounding to pipes up to 1") Six feet long.
Grounding Cord, gator/clamp (Cat. #A295-gc) ..... $8.95 add to cart



Grounding Cord

Gator to Ring

Alligator clip on one end, ring terminal on the other (great for connecting to the faceplate screw on an electric outlet. Wire length: Six feet long.
Grounding Cord, gator/ring 72 inch (Cat. #A295-gr) ..... $6.00 add to cart



FUSE FOR GROUND CORDS

IN LINE FUSE HOLDER

Adds a Measure of Safety

To add a measure of safety to any cord in the unlikely event of a lightning strike or voltage spike traveling on your electrical system, you can insert this handy fuse anywhere along the length of the wire. Set includes fuse holder, two 0.10 Amp fuses (one is a spare), and two wire nuts.
In Line Fuse Holder (Cat. #A286) ............... $4.95 add to cart

Replacement Fuses pack of 5 (Cat. #A287) ...... $4.95 add to cart



3 OUTLET SOCKET ADAPTER 3 OUTLET SOCKET ADAPTER

3 OUTLET SOCKET ADAPTER

More Outlet Space 3 OUTLET SOCKET ADAPTER

Need more room for your high frequency filters or ground cords? This sturdy adapter converts one outlet into three. Uses standard North American 3-prong outlet. Handles up to 15A safely. Color/style may vary.
3 Outlet Socket Adapter (Cat. #A804) .............. $2.95 add to cart



Body Voltage Meter

BODY VOLTAGE METER

Measure the Voltage Effects of EMF on Your Body!

An external field will induce an electric field within our bodies. In this sense, our bodies act as antennas picking up fields from electric blankets, alarm clocks, powerlines, and just about everything connected to a source of electric power.

Delicate biological cellular processes (like brain function and heart muscle contraction) operate on the scale of microVolts to milliVolts. Body Voltage can exceed several Volts in some cases.

Body Voltage Meter

The Body Voltage Meter quickly and easily reports this induced AC body voltage. Simply hold the sensor handle. Notice how your body voltage varies as you move about the room, as you change position (standing vs lying down, for example) and it also depends on what you are wearing.

The Body Voltage Meter is a great way to test the effectiveness of your static discharge (ESD) devices and can be used to measure the AC voltage build up on static producing surfaces. Large digital readout is easy to see and sensitive down to 1 mV. Will help you detect irritating voltage sources which may not otherwise be obvious. Comes complete. Uses 1 9V battery (not included). Calibrated for 40-500 Hz.

Body Voltage Meter (Cat. #A183N)....................$89.95 add to cart



Body Voltage Meter

Body Voltage Meter, now available with Ground Stake

Use True Earth as Your Reference

If you prefer to ground to soil, this version of our popular Body Voltage meter comes with a 4 foot copper-plated steel rod and 50 feet of cord so you can ground directly to Earth for confident readings. This is especially important when:
1- You don’t have a convenient electrical ground to work with
2- You are working outdoors
3- You have voltage or dirty electricity on your ground lines
4- You don’t trust the ground in your building

Simply push the ground rod into the soil and run the ground cord to the location where you want to perform your body voltage measurements.

Body Voltage Meter with Ground Stake (Cat. #A183-stake)....................$129.90 add to cart


Need more cable? 50’ Banana Extension
This handy 50 ft extension cable has banana male on one end, female on the other. You can daisy chain as many as you like to achieve the desired length.
50’ Banana Extension (Cat. #A291-ext)....................$19.95 add to cart



Alligator Clips

ALLIGATOR CLIPS


High quality alligator clips for grounding and conductivity uses. Will grab foils, fabrics, chassis, grounding wires, screws, and small posts. Attach to just about any copper wire with solder or crimp.


Alligator Clip (Cat. #A298) ........... $2.00/pair add to cart



GROUNDING CLAMP

Grounding Clamp

Attaches Ground Cords to Pipe

Nickel plated clamp with good jaw tension capable of grabbing ¼" to 1" diameter pipe, screw or bar. Use these to attach ground cord to your plumbing, or to metal stakes in the ground. Crimps easily to cord. 4" length overall. Ground cord not included.

Grounding Clamp (Cat. #A296) …........... $4.95 add to cart



SNAP / RING TERMINAL COMBINATION

Alligator Clips

Attaches Ground Cords to Fabric or Plastic

Want a tidy and good looking way to attach a ground cord to a conductive fabric or plastic shield? This simple hardware combination does the trick in style. First, crimp the provided ring terminal to your ground wire. Next, punch a small hole in your conductive sheet. Pass the stud of the snap through this hole and through the ring terminal. Finally, apply the other half of the snap. Makes good contact and you can move it or remove it as needed. Snap is nickel plated for excellent corrosion resistance and is washable. Ground wire not included.

Snap/Ring Terminal Combination (Cat. #A294) …. $2.00 per set add to cart



GROUND STAKE KIT

Ground Stake Kit Ground Stake Kit

If you don’t like the idea of grounding your shielding paint, fabric or plastic through your building’s electrical system, you can use this simple and durable grounding stake to connect directly to the Earth. Sturdy, rust resistant, 48 inch long, 11/32" diameter Copper plated steel stake is ready to drive into the soil. Complete with exterior grade, 18 gauge ground cord (with no terminal) and stake-to-cord connector.

Note: if soil is rocky, you may need to dig a hole first with appropriate tools. Be careful when selecting location… do not puncture buried wires or pipes.

Ground Stake Kit, 50 ft cable (Cat. #A291-50) .............. $39.95 add to cart


Poor soil for grounding?

Sheffield Pottery offers high conductivity soil and soil additives to make your soil a better ground (more conductive).



Portable Ground Stake

PORTABLE GROUND STAKE

Easy to Carry, Easy to Set

Travelling? Grounding at the park, beach, or back yard? When you need a less permanent grounding point, this is the easy way to do it. 18 inch long, chrome plated steel with corkscrew tip and comfy handle. A few turns of the wrist sets it into the soil, and removes it just as easily. Wire clamp and 10 feet of 18 gauge stranded ground cord with gator clip included.

Portable Ground Stake (Cat. #A297) .............12.95 add to cart



Velcro A-S Wrist Strap

VELCRO ANTI-STATIC WRIST STRAP

  • comfortable 2 cm wide, black nylon Velcro strap
  • interior surface is coated with conductive carbon
  • completely adjustable
  • coil cord with 1 Mohm resistor, connects to strap with snap, stretches to 60 inch
  • cord terminates with banana plug or alligator clip (included)

Velcro A-S Wrist Strap (Cat. #A469) …… $3.95 add to cart

Velcro A-S Wrist Strap



Fabric Wrist Strap

FABRIC ANTI-STATIC WRIST STRAP

  • comfortable 2 cm wide, elastic blue nylon strap
  • interior surface is highly conductive metalized threads
  • completely adjustable
  • 4 mm male snap
  • ground cord with 1 MegOhm resistor, included


Fabric Wrist Strap (Cat. #A243) …… $2.00 add to cart



Gray Conductive Socks Gray Conductive Socks

GRAY CONDUCTIVE SOCKS

High Silver Content

These socks start with a polyester fiber which is twisted with pure Silver fibers, then knit into the sock shape, giving it a very high conductivity (only a few Ohms across) and good shielding performance throughout. Reasonably soft and stretchy with ribbed cuff. Socks include a 1.7 mm male snap near the cuff. Great for RF shielding, grounding, and can even be used for TENS applications. Hand washable. Fits shoe size 5-10.

Conductive Socks - gray (Cat. #A352) ............ $19.95/pair add to cart


What our customers tell us:

"I got a pair of conductive socks and a (ground) cord. That evening and put the socks on, connected them to the ground wire and sat down to read a book. I woke up 2 hours later, still on the same page I had started on. I took the socks off and got ready for bed. When I went to bed, I went to sleep immediately and slept about 8 or 9 hours. As I was walking around the next morning, I noticed that the pain in my hips and knees was almost unnoticeable."

M.R., Woodside CA



SHIELDED GLOVES

The Finger Faraday Cage!

Shielded Gloves Shielded Gloves For those of you who experience (or want to prevent) ES symptoms in your hands when using a computer keyboard, laptop, cell phone or other electronic devices, these gloves form a conductive enclosure and effectively shield radiowaves and electric fields. Soft, light weight, with ribbed cuff, and offering good tactile sensitivity. Polyester fiber is twisted with pure Silver fibers, then knit into a stretchy glove shape in basic gray color. Each glove has a 1.7 mm snap for a ground cord. Fully hand washable and tested for 50 cycles with no appreciable loss of conductivity. All fibers are conductive, achieving resistivity of less than 10 Ohm/sq. These gloves are also used in industry for static control when working with delicate static sensitive components and can even be used for TENS applications. Grounding is not necessary for Faraday Cage shielding effect, but is necessary for static control. Also useful on touch screens like an iGlove. We do not have the ground cord which fits this snap on these gloves. Shielded Gloves:

Child Size (Cat. #A351-c)...............................$16.95 add to cart

Adult Size (Cat. #A351-a)..............................$16.95 add to cart



Socket Tester Including Proper Ground Test

SOCKET TESTER
INCLUDING PROPER GROUND TEST

Check Sockets for Improper Wiring and Faulty Ground!

You know what happens when we ass-u-me? Electric sockets can be bad for a number of reasons: a wire can short or fray, a wire can become disconnected, or corrode at the contact, or the wires can be connected to the wrong contact altogether! These problems can be a fire hazard, a shock hazard, a problem for polarized appliances, and definitely a problem if you are using the socket’s ground connection to Earth your shielding.

There is no need to guess because it is so easy to test for proper wiring at a socket. Simply plug in the tester and look at the result. Large LCD display indicates if ground is missing or faulty. Easy to see LEDs light up to indicate all these possible problems:
Socket Tester Including Proper Ground Test

- Voltage on ground connection
- Disconnected Ground
- Disconnected Neutral
- Disconnected Hot
- Interchanged Neutral and Hot
- Interchanged Ground and Hot
- Interchanged Ground and Hot, Neutral missing
- GFI function

This inexpensive tester can be used over and over and gives either peace of mind or a specific learning about what to do. Don’t ground to your socket without it! North American Plug only. Rated for 120V, 50/60 Hz.

Socket Tester Including Proper Ground Test (Cat. #A452) ... $14.95 add to cart



Ni/Cu/Co FABRIC TAPE

Copper Fabric Tape

"Conductive Adhesive Too!"

High conductivity, high flexibility fabric tape with conductive adhesive. Copper Fabric Tape Shielding Performance Nickel, Copper and Cobalt coated nylon ripstop fabric (with anti-fray) offers excellent RF shielding properties (70 dB at 1 MHz, 100 dB at 1 GHz) and electrical conductivity (surface resistivity of less than 0.1 Ohms/sq). Use it so seal gaps, seams, and edges of shielding fabrics, paints or plastics. Also can be used to create conductive pathways on surfaces or add shielding to cables and flexible conduits. Cuts easily with scissors. Extremely corrosion and tear resistant, -10 to 80°C. Only 0.005 inch thick. 1 inch wide, 25 feet per roll with paper release liner.

Nickel/Copper/Cobalt Fabric Tape (Cat. #A225) …… $19.95/roll add to cart



Heel Ground Heel Ground

HEEL GROUND

"Makes any Shoe into a Grounding Device"

Perhaps the easiest way to stay grounded when you are on the go. Conductive rubber material is black on one side, blue on the other, discharges you to whatever surface you are standing on. Non-marking on most surfaces. Slip over the heel and wrap the adjustable Velcro™ strap around the front of your ankle to hold it in place. Conductive tag can go inside the shoe or into the top of your sock to make contact with your skin. Includes 1 MegOhm resistor. Static dissipation to zero volts is accomplished in less than 0.1 seconds on any conductive surface. Perfect for static discharge and ESD applications. You get 1 per order.

Heel Ground (Cat. #A242) ............... $5.95 add to cart



ANTI-STATIC MAT

"Now With Washable Ex-Static™ Cover"

Anti-Static Mat You can ground a useful (12" x 12") area with this professional quality heavy duty static control mat. Use it with static sensitive computer equipment or as a surface for handling static sensitive semi-conductors. Put it under your keyboard or laptop.

Anti-Static Mat More importantly, you can simply touch the mat with any part of your body to dissipate electric field build-up and equalize your potential with ground and reduce static discharge problems. Put it on your seat or on your desktop to reduce ESD. Can be trimmed with scissors to fit any area. Includes removable and washable Ex-Static™ fabric cover, and 5 foot grounding cord (no resistor), terminates with an alligator clip. If you want to ground to your electric outlet, get a plug to gator ground cord). Surface resistivity is only 105 Ohm/sq. Tough black rubber, about 1/16" thick, for years of trouble free service.

This pad is for static discharge and grounding of radiofrequency shelding. We do not make any claims for health benefits of body grounding with this product.

Anti-Static Mat (Cat. #A212) ......................…. $39.95 add to cart


Link to: Study on the benefits of grounding during sleep by Clint Ober



Anti-Static Mini Pad

ANTI-STATIC MINI PAD

"Small Price, Big Performance"

Static Electricity accumulates as you walk and move about. Once you build enough static charge your body can get a shock when you touch another conductive object. After this discharge, your body begins the static building process again as you continue to move about. The discharge is not only painful to you but it can also be destructive to the object you touch… like a phone, computer or any electronic component.

To eliminate the pain and save your electronic equipment place Anti-Static Mini Pads at strategic locations (your desk, computer, fax, file cabinet). Touch them often. Touch it with your hand, toe, nose or any part of your body. No pain, no damage, as you are now at zero static. 4x6 inches. 109 Ohm/sq. Includes 10 foot cord with 1 MOhm resister which snaps on, and terminates with an “O” ring.
Anti-Static Mini Pad (Cat. #A350) ........... $10.95 add to cart



METAL FOIL TAPE

"Self Adhesive and Great for Shielding Projects"


ALUMINUM FOIL TAPE
Aluminum Foil Tape Perfect for Small RF Shielding Jobs

2 mil thick aluminum alloy foil with a pressure-sensitive synthetic rubber adhesive and paper liner. The aggressive rubber adhesive sticks well to most surfaces and the paper liner makes for convenient and reliable use. Great for shielding small areas, or wrapping cable. 1.89 inches wide and highly conformable, total thickness is only 3.6 mil. Can be used under all weather conditions. Resists water vapor, odor and smoke transmission. Application/use temperature range: +10°F to +180°F. Each roll is 30 feet long.

Aluminum Foil Tape (Cat#A229) …...... $4.95/roll add to cart



ELECTRIC PAINT AND ADHESIVE

ELECTRIC PAINT AND ADHESIVE

Great Way to Connect Leads to a Conductive Fabric

Working without alligator clips or snaps? This nontoxic, solvent free and water soluble material spreads easily and dries quickly to form a conductive bond between most surfaces. Just squeeze a little bit onto your fabric, embed the bare copper wire lead into it and wait about an hour. It adheres well to a wide range of synthetic and natural fabrics. Note that Electric Paint is water soluble, washing with soap and water will remove any paint which has been applied. If you want to make it more durable, you can use waterproofing spray to protect the surface of the fabric. Use it to make conductive traces, repair circuit boards, even make smart textiles!

The paint’s conductive properties do not degrade over time. In-house samples demonstrate that the material can last years if treated properly and kept dry. Electric Paint is well suited for screen-printing with meshes ranging from 43t to 90t. The paint is slightly resistive- at approximately 55 ohms per square. The conductivity of Electric Paint increases as it dries, therefore wait until it is completely dry to test your projects. 10ml squeeze tube. Black.

Electric Paint (Cat. #A701) ............. $12.95 add to cart



The following items are available from other websites. We provide this information as a courtesy. These websites have no affiliation with Less EMF Inc. Proceed at your own risk:

Earthing Shoes and Sandals

          Pluggz      Pluggz




Earthing
Universal Mat
with Cover Kit

Earthing Half Sheet Kit

Earthing Starter Kit

Earthing Recovery Bag Kit

Earthing: book

Earthing
Patch Kit

Earthing
Throw Kit

Earthing
Fitted Sheet Kit

Earthing/Grounding
Pillowcase With Tester

Earthing Recovery Bag
with Tester


Home Go To Checkout

LessEMF.com
776B Watervliet Shaker Rd      Latham NY 12110-2209      USA
Order Toll Free: (8 8 8) 5 3 7 - 7 3 6 3
International: +1   ( 5 1 8 )   6 0 8 - 6 4 7 9
Fax: +1   ( 3 0 9 )   4 2 2 - 4 3 5 5

Send E-Mail to Less EMF Inc.
lessemf@lessemf.com

home emf
meters
emf
shielding
emf
books
emf
appliances
sale
items
order
form

Copyright 1996-2016, Less EMF Inc.